fbpx

Advice

Viewing 15 posts - 1 through 15 (of 18 total)
  • Author
    Posts
  • #689134

    Hello my friends,

    Does anyone have any experience with removing acrylic from the small details of their PYO’s.

    So far I’ve tried 70% alcohol and a tooth brush with limited success.

    Would really like to get the detail crevices as clean as possible with damaging the texture. I’ve touched it with a very fine dental pick, but that tends to introduce scribe lines.

    Any sure fire homebrews that will not cause damage to the cast?

    Thanks!

    #495045

    #689135

    Citristrip works very well, as does acetone. With both, be prepared to have to glue the eyes back in, as it will dissolve the glue holding them in, but the upside is that painting is easier without them in.

    Good luck.

    Kyrin

    #689136
    Andrea
    Participant

      Have you thought of spay primer? That way you don’t have to worry about the solvent eating the gypsum away or rining the statue.

      #689137

      Phoenix wrote:

      Have you thought of spay primer? That way you don’t have to worry about the solvent eating the gypsum away or rining the statue.

      Perhaps I am being a bit sensitive today, but your comment seems to be saying that my suggestion would damage the piece. Considering I have now stripped down two dragons down to bare gypsum using these two solutions without damaging them, I feel kind of offended and hurt.

      Kyrin (please note that I did mention I might be feeling a bit sensitive today)

      #689138

      It worked, I did not soak the piece. Just loaded a toothbrush with acetone and scrubbed away.

      Cleaned out all the nooks and crannies. Rinsed it with soapy water, and letting it dry (it’s almost 90 degrees today, so it won’t be long). The eyes stayed put, but I was pretty careful on where I applied the solvent.

      Thanks Kyrin !

      Phoenix, the reason I did not want to add additional paint was due to the issue of detail lost with buildup. I am going to airbrush, so the coats will be fairly thin. Thought it better to retain as much of the original surface detail as possible. Plus I want lighter colors which would require quite a bit of heavy pigment to cover the darker old paint.

      It’s a learning curve for me, so I appreciate the suggestions.

      #689139
      Jodi
      Participant

        Kyrin wrote:

        Phoenix wrote:

        Have you thought of spay primer? That way you don’t have to worry about the solvent eating the gypsum away or rining the statue.

        Perhaps I am being a bit sensitive today, but your comment seems to be saying that my suggestion would damage the piece. Considering I have now stripped down two dragons down to bare gypsum using these two solutions without damaging them, I feel kind of offended and hurt.

        Kyrin (please note that I did mention I might be feeling a bit sensitive today)

        I don’t think Phoenix meant anything negative about your comment, but just gave another suggestion to someone who may be too nervous to try your expert method. It’s good to get a lot of different input on things, so the person attempting it can decide which one is right for him/her. Don’t take offense. Eat chocolate. 😀

        #689140

        emerald212 wrote:

        Kyrin wrote:

        Phoenix wrote:

        Have you thought of spay primer? That way you don’t have to worry about the solvent eating the gypsum away or rining the statue.

        Perhaps I am being a bit sensitive today, but your comment seems to be saying that my suggestion would damage the piece. Considering I have now stripped down two dragons down to bare gypsum using these two solutions without damaging them, I feel kind of offended and hurt.

        Kyrin (please note that I did mention I might be feeling a bit sensitive today)

        I don’t think Phoenix meant anything negative about your comment, but just gave another suggestion to someone who may be too nervous to try your expert method. It’s good to get a lot of different input on things, so the person attempting it can decide which one is right for him/her. Don’t take offense. Eat chocolate. 😀

        That’s it, no chocolate yet today! I knew there was a reason I was feeling sensitive! 🙂

        Seriously though, I know Phoenix didn’t mean anything, but word choices do put a spin on things. Which is why I said something, since her choices here made me feel kinda bad without meaning to.

        Kyrin

        #689141
        Jodi
        Participant

          Kyrin wrote:

          emerald212 wrote:

          Kyrin wrote:

          Phoenix wrote:

          Have you thought of spay primer? That way you don’t have to worry about the solvent eating the gypsum away or rining the statue.

          Perhaps I am being a bit sensitive today, but your comment seems to be saying that my suggestion would damage the piece. Considering I have now stripped down two dragons down to bare gypsum using these two solutions without damaging them, I feel kind of offended and hurt.

          Kyrin (please note that I did mention I might be feeling a bit sensitive today)

          I don’t think Phoenix meant anything negative about your comment, but just gave another suggestion to someone who may be too nervous to try your expert method. It’s good to get a lot of different input on things, so the person attempting it can decide which one is right for him/her. Don’t take offense. Eat chocolate. 😀

          That’s it, no chocolate yet today! I knew there was a reason I was feeling sensitive! 🙂

          Seriously though, I know Phoenix didn’t mean anything, but word choices do put a spin on things. Which is why I said something, since her choices here made me feel kinda bad without meaning to.

          Kyrin

          *passes Kyrin chocolate* I just had the best drink… a dark chocolate Starbucks Frappuccino. Yum! I recommend it for instant attitude adjustments. 😀

          #689142
          frozendragon
          Participant

            hmm…have you tried the black and white mocha…

            dark chocolate and white chocolate….yummy…

            and I’m about to try the citris stripper stuff on a PYO I have too…

            we’ll see how it works… 😀

            #689143
            Mmloda
            Participant

              I`ve always used nail polish remover with acetone and water to rinse ot off after…. 😀

              Marzena

              #689144
              Andrea
              Participant

                Nope, not saying your method was bad, just offering another method someone had suggested in the past when the question was asked.

                #689145
                Jodi
                Participant

                  frozendragon wrote:

                  hmm…have you tried the black and white mocha…

                  dark chocolate and white chocolate….yummy…

                  and I’m about to try the citris stripper stuff on a PYO I have too…

                  we’ll see how it works… 😀

                  I have not hadthe black and white mocha. I’ve never even seen it around here. I’ll have to look for it. I’ve had the dark chocolate mint that was out at Christmas time. That was yummy too!

                  #689146

                  mmloda wrote:

                  I`ve always used nail polish remover with acetone and water to rinse ot off after…. 😀

                  Silly Mmloda, nail polish remover is acetone, it just has extra vitamin E…you goof! 😆 😆

                  Kyrin

                  #689147

                  Hmmm…I’m not sure if this thread makes me want to go paint my nails, or drink coffee… 😯 😆

                Viewing 15 posts - 1 through 15 (of 18 total)
                • You must be logged in to reply to this topic.